21 December 2018

Twisting Light to Enable High-Capacity Data Transmission

 

21 December 2018

 

Twisting Light to Enable High-Capacity Data Transmission

Tiny gears on computer chips generate a vortex of light that could boost optical computing

 

WASHINGTON — For the first time, researchers have used tiny gears made of germanium to generate a vortex of twisted light that turns around its axis of travel much like a corkscrew. Because germanium is compatible with the silicon used to make computer chips, the new light source could be used to boost the amount of data that can be transmitted with chip-based optical computing and communication.

 

The researchers, from the University of Southampton in the U.K., and University of Tokyo, Toyohashi University of Technology and Hitachi Ltd., all in Japan, describe the new light-emitting gears in The Optical Society (OSA) journal Optics Express. With a radius of one micron or less, 250,000 of the gears could be packed into just one square millimeter of a computer chip.

 

There is a great deal of interest in generating light that is twisted, or has orbital angular momentum, because of its advantages for communications and computing. Today, light is used to carry information by varying the number of photons emitted or switching between light’s two polarization states. With twisted light, each twist can represent a different value or letter, allowing the encoding of a great deal more information using less light.

 

“Our new microgears hold the potential for a laser that can be integrated on a silicon substrate— the last component needed to create an integrated optical circuit on a computer,” said the paper’s first author Abdelrahman Al-Attili, from the University of Southampton. “These tiny optical-based circuits use twisted light to transmit large amounts of data.”

 

Using strain to improve light emission

It has been impossible to make a usable miniaturized light source on silicon, the material commonly used to make computer chips and associated components, because the material’s properties led to poor light-generating efficiency. Although germanium has similar limitations, applying strain by stretching it can improve its light emission efficiency.

 

“Previously, the strain that could be applied to germanium was not large enough to efficiently create light without degrading the material,” said Al-Attili. “Our new microgear design helps overcome this challenge.”

 

The new design features microgears that are freestanding at the edges so that they can be stretched by an oxide film deposited over the structures. This allows tensile strain to be applied without breaking the germanium’s crystal structure. The gears stand on a silicon pedestal that connects it to the top of the silicon substrate and allows heat to dissipate during operation.

 

To demonstrate their new design, the researchers used electron beam lithography to fabricate the very fine physical features that form the gears’ teeth. They then illuminated the gears with a standard green laser that did not emit twisted light. After the microgear absorbed the green light it generates its own photons that are circulated around the edges forming twisted light that is reflected vertically out of the gear by the periodic teeth.

  

Precision optical simulations

The researchers tested and tweaked their design using computer simulations that model the way light propagates in the gears over nanoseconds or even shorter time periods. By comparing the prototype’s light emission with computer simulation results, they were able to confirm that the gears generated twisted light.

 

“We can precisely design our device to control the number of rotations per propagation wavelength and the wavelength of the emitted light,” said Al-Attili.

 

The researchers are now working to further improve the efficiency of light emission from the germanium microgears. If successful, this technology would make it possible to integrate thousands of lasers onto a silicon chip for transmitting information.

 

“Silicon fabrication technologies that were developed to make electronic devices can now be applied to make various optical devices,” said Al-Attili. “Our microgears are just one example of how these capabilities can be used to make nano- and microscale devices.”

 

This research is supported by the Engineering and Physical Sciences Research Council (EPSRC).

 Paper: A. Z. Al-Attili, D. Burt, Z. Li, N. Higashitarumizu, F. Y. Gardes, K. Oda, Y. Ishikawa, S. Saito, “Germanium vertically light-emitting micro-gears generating orbital angular momentum,” Opt. Express, 26, 26, 34675-34688  (2018).

DOI: •https://doi.org/10.1364/OE.26.034675.

 

About Optics Express

Optics Express reports on new developments in all fields of optical science and technology every two weeks. The journal provides rapid publication of original, peer-reviewed papers. It is published by The Optical Society and edited by Andrew M. Weiner of Purdue University. Optics Express is an open-access journal and is available at no cost to readers online at: OSA Publishing.

 

About The Optical Society

Founded in 1916, The Optical Society (OSA) is the leading professional organization for scientists, engineers, students and business leaders who fuel discoveries, shape real-life applications and accelerate achievements in the science of light. Through world-renowned publications, meetings and membership initiatives, OSA provides quality research, inspired interactions and dedicated resources for its extensive global network of optics and photonics experts. For more information, visit osa.org.

 

Media Contact:

mediarelations@osa.org